[ U = 1 - \frac{1.13}{6} = 0.812 ]
Gross shear length = ( 1.5 + 3 + 3 = 7.5 \text{ in} ) (from edge to last bolt). Net shear length = ( 7.5 - 2.5 \times d_h = 7.5 - 2.5 = 5.0 \text{ in} ) (since 2.5 holes along shear path? Actually 2.5 holes for two lines? Need precise – typical simplified: net shear area = ( (7.5 - 2.5*(1.0))*0.5 = 2.5 \text{ in}^2 ) per plane, two planes = 5.0 in²).
Check alternative staggered path through first hole in one leg then to hole in opposite leg? For L4×4, gage between legs (distance from back of one leg to center of holes in other leg) ≈ 2.5 in (AISC gage for angles). But given gage = 2.0 in, stagger term: ( s^2/(4g) = 3^2/(4 2) = 9/8 = 1.125 ). For one diagonal path: ( A_n = A_g - 2 (d_h t) + (1.125 t) ) = ( 3.75 - 1.0 + 0.5625 = 3.3125 \text{ in}^2 ) → larger than 2.75, so critical net area = 2.75 in².
So ( R_n = 191 \text{ kips} ) (lower governs). This is much higher than tensile fracture or yielding – thus block shear does not control. solution manual steel structures design and behavior
A single-angle tension member, L4×4×½ (A36 steel), is connected to a gusset plate with 7/8-inch diameter bolts as shown in Figure P2.17 (three bolts in one leg, staggered: 3" on center along length, 2" gage). Compute the design tensile strength (LRFD) and allowable tensile strength (ASD).
Yielding: LRFD 121.5 kips, ASD 80.8 kips Fracture: LRFD 97.1 kips, ASD 64.8 kips →
[ R_n = 0.6 F_u A_{nv} + U_{bs} F_u A_{nt} \quad \text{with } U_{bs}=1.0 \text{ (uniform tension)} ] [ R_n = 0.6 \times 58 \times 5.0 + 1.0 \times 58 \times 0.5 = 174 + 29 = 203 \text{ kips} ] But limited by ( 0.6 F_y A_{gv} + U_{bs} F_u A_{nt} = 0.6 \times 36 \times 7.5 + 29 = 162 + 29 = 191 \text{ kips} ) [ U = 1 - \frac{1
Better to follow AISC manual example: For L4×4×½ connected with 3 bolts, block shear strength:
[ A_n = A_g - \sum (d_h \cdot t) + \sum \left( \frac{s^2}{4g} \cdot t \right) ]
Given edge distance = assume 1.5 in (standard), spacing = 3 in, hole diameter = 1 in, thickness = 0.5 in. Need precise – typical simplified: net shear area = ( (7
[ P_{n, yielding} = F_y \cdot A_g = 36 \cdot 3.75 = 135 \text{ kips} ]
For L4×4×½: ( \bar{x} = 1.13 \text{ in} ) (from AISC Manual). Length of connection ( L ) = distance between first and last bolt = 2 pitches = 6 in.
Tension member connected to gusset plate – check block shear along bolt group.
LRFD: ( \phi_t = 0.75 ) → ( P_d = 0.75 \times 129.5 = 97.1 \text{ kips} ) ASD: ( \Omega_t = 2.00 ) → ( P_a = 129.5 / 2.00 = 64.8 \text{ kips} )