Magnetic Circuits Problems And Solutions Pdf Apr 2026

So: [ \mathcalR_eq, branches = \frac(\mathcalR_o + 2\mathcalR_y)2 = \frac530.5 + 132.62 = 331.55 \ \textkA-t/Wb ] Wait – (2\mathcalR_y = 132.6), so (\mathcalR_o + 2\mathcalR_y = 530.5+132.6 = 663.1). Half of that is kA-t/Wb.

Reluctance without gap: [ \mathcalR c,iron = \frac0.15(4\pi\times 10^-7)(600)(4\times 10^-4) \approx 497.4 \ \textkA-t/Wb ] MMF = (\Phi \mathcalR) → (250 = (1.2\times 10^-3) \times \mathcalR total,des ) So (\mathcalR_total,des \approx 208.3 \ \textkA-t/Wb) – but that’s than iron reluctance alone? That’s impossible.

Ah – critical insight: If the core originally had , its reluctance is 497 kA-t/Wb. Then flux would be (250/497k \approx 0.503 \ \textmWb), not 1.2 mWb. So the “desired” 1.2 mWb must have come from a different core or higher current. The problem as written is inconsistent – an excellent teaching point: always check if numbers make physical sense . magnetic circuits problems and solutions pdf

Percent change from Problem 2: [ \frac0.232 - 0.2010.201 \times 100 \approx +15.4% ] Fringing reduces reluctance → increases flux. Ignoring fringing underestimates performance. Solution 4 – Series-Parallel Circuit Step 1 – Reluctances (all (\mu = 1000 \mu_0))

Center limb: [ \mathcalR_c = \frac0.1(4\pi\times 10^-7)(1000)(6\times 10^-4) \approx 132.6 \ \textkA-t/Wb ] Each outer limb: [ \mathcalR_o = \frac0.2(4\pi\times 10^-7)(1000)(3\times 10^-4) \approx 530.5 \ \textkA-t/Wb ] Yoke (each, two yokes in series effectively for each flux path): [ \mathcalR y = \frac0.05(4\pi\times 10^-7)(1000)(6\times 10^-4) \approx 66.3 \ \textkA-t/Wb ] Total for one outer path (center → yoke → outer limb → yoke → center): [ \mathcalR outer, total = \mathcalR_c + 2\mathcalR_y + \mathcalR_o ] [ = 132.6 + 2(66.3) + 530.5 = 795.7 \ \textkA-t/Wb ] But careful: The two outer paths are after the center limb. That’s impossible

MMF: (\mathcalF = NI = 200 \times 2 = 400 \ \textA-turns) [ \Phi = \frac\mathcalF\mathcalR_c = \frac400398 \times 10^3 \approx 1.005 \ \textmWb ]

Mistake: Desired flux is (1.2\ \textmWb) – that’s higher than actual? No, problem says: after fault, measured flux = 0.8 mWb at same current. So with fault: [ \mathcalR total,fault = \frac2500.8\times 10^-3 = 312.5 \ \textkA-t/Wb ] Without fault, if no gap: (\mathcalR iron \approx 497\ \textkA-t/Wb) – but that would give even lower flux? Contradiction. So the “desired” 1

Given: Core length (l_c = 0.15 \ \textm), area (A = 4 \ \textcm^2), (\mu_r = 600) (still valid). What is the effective air gap length that explains the reduced flux? (Ignore fringing first, then discuss if fringing would make the gap larger or smaller.) 3. Complete Solutions Solution 1 – Toroidal Core (a) Reluctance of core: [ \mathcalR_c = \fracl_c\mu_0 \mu_r A = \frac0.4(4\pi \times 10^-7)(800)(5\times 10^-4) ] [ \mathcalR_c = \frac0.4(1.0053 \times 10^-3) \approx 398 \ \textkA-turns/Wb ]

The center limb carries (\Phi_c). That flux splits into two paths, each with total reluctance (\mathcalR_branch = \mathcalR_o + 2\mathcalR_y). The center limb reluctance is in series with the parallel combination of the two branch reluctances.

Hint: By symmetry, the two outer limbs carry equal flux. A DC relay has a magnetic circuit that should produce (\Phi = 1.2 \ \textmWb) at (I = 0.5 \ \textA) with (N = 500). After years of use, the measured flux is only (0.8 \ \textmWb) at the same current. You suspect an unexpected air gap has developed (e.g., due to corrosion or mechanical wear).